CreatBot 2,85 mm Wire feeder block L/1
5 disponibili
Replacement wire feeder block (variant L/1) for CreatBot extruders using 2.85 mm filament. Serves as the housing/guide around the drive mechanism to support consistent filament feeding into the hotend.
Key Features
Compatibility: CreatBot extruder systems for 2.85 mm filament (L/1 position).
Function: Guides and supports the drive gear/idler path for stable feeding.
Direct 1:1 replacement; fits original mounting points and connectors.
Helps restore reliable extrusion when the original block is worn or damaged.
Designed for tidy cable/filament routing in the factory layout.
Installation tip: power off, keep the filament path clean, and verify extrusion after swap.
41,41€
5 disponibili
Blocco feeder L/1 per configurazioni CreatBot da 2,85 mm. Sostituisce un alloggiamento usurato per ripristinare una guida del filamento fluida e affidabile. Installare con l’alimentazione spenta e successivamente testare l’estrusione.
CreatBot 2,85 mm Wire feeder block L/1
Based on 0 reviews
Be the first to review “CreatBot 2,85 mm Wire feeder block L/1”
You must be logged in to post a review.
Prodotti correlati
-
3D World, Filamenti & Resine 3D
PORO-LAY – LAYFOMM 60, 3.00 mm, 0.25 kg
LAY-FOMM 60 is the newest innovation from the creator of LAYBRICK, LAYWOO-D3, and BendLay. LAY-FOMM 60 is a foamy material and is highly porous. LAY-FOMM 60 is part rubber-elastomeric polymer and part PVA. Once you rinse this material in water only the rubber polymer remains as your micro-porous and flexible object. LAY-FOMM 60 is slightly firmer than LAY-FOMM 40.
Main features
After printing rinse with water to create an object that is micro-porous & elastic
Optimal for printing soft rubber objects
All objects are hot-sealable after drying
the objects have near zero warp (deformation while printing)SKU: 0634654248404 -
3D World, Filamenti & Resine 3D
PORO-LAY – GELLAY – 1.75mm – 0.25 kg
Gellay filament from the Porolay series is a very special material. With it, soft parts can be created and you can finally print out your organs from the 3D printer – of course not functional. But for e.g. aquaristics from the 3D printer, this gel-like printing material is very exciting. Like all other Porolay filaments, Gellay is also hard in its initial state and easy to print.
Main features
When wet: gel-like and very soft
In dry state: Stable, not elastic but bendable
Perfect for soft tissues
Low warpingSKU: 0634654248411 -
3D World, Filamenti & Resine 3D
PORO-LAY – LAYFOMM 40, 3.00 mm, 0.25 kg
LAY-FOMM 40 is the newest innovation from the creator of LAYBRICK, LAYWOO-D3, and BendLay. LAY-FOMM 40 is a foamy material and is highly porous. LAY-FOMM 40 is part rubber-elastomeric polymer and part PVA. Once you rinse this material in water only the rubber polymer remains as your micro-porous and flexible object.
Main features
After printing rinse with water to create an object that is micro-porous & elastic
Optimal for printing soft rubber objects
Polymer components of LAY-FOMM 40 are harmless and foodsafe.
All objects are hot-sealable after dryingSKU: 0634654248381 -
3D World, Filamenti & Resine 3D
PORO-LAY – GELLAY – 3.00mm – 0.25 kg
Gellay filament from the Porolay series is a very special material. With it, soft parts can be created and you can finally print out your organs from the 3D printer – of course not functional. But for e.g. aquaristics from the 3D printer, this gel-like printing material is very exciting. Like all other Porolay filaments, Gellay is also hard in its initial state and easy to print.
Main features
When wet: gel-like and very soft
In dry state: Stable, not elastic but bendable
Perfect for soft tissues
Low warpingSKU: 0634654248428
There are no reviews yet.